da LupinIII » mar nov 27, 2007 8:36 am
ti posto il log dell'hdd.
la temperatura è bassa perché è appena stato acceso.
pero' ieri sera dopo aver fatto un trasferimento di dati da uno all'altro, ho notato che un avviso recava la scritta temperatura elevata. 46°.
penso si astato riferito all'hdd numero 1.
46° è elevata, oppure durante un trasferimento puo' essere che salga vertiginosamente la temp?
potrebbe essere necessario installare una ventola supplementare?
una piccola cosa.
ieri sera ho slavato un file, lo ho riaperto dopo circa qualche secondo e presentava delle righe.
penso che oggi cambiero' il cavo ide.
Drive model ST3160215A
Drive capacity 134,2 GB
Drive serial number 9RA2NACD
Firmware revision 3.AAD
Number of cylinders 16383
Number of heads 16
Number of sectors per track 63
Number of LBA sectors 268435455
DMA support Enabled
LBA support Enabled
IORDY support Enabled
ATA software reset Not required
Overlap operation Supported
Command queuing Not supported
Interleaved DMA Not supported
Multiword DMA mode supported Mode 2 and below
PIO transfer mode supported Mode 4
Minimum Multiword DMA transfer cycle time per word 120 nostro
Manufacturer’s recommended Multiword DMA transfer cycle time 120 nostro
Minimum PIO transfer cycle time without flow control 240 nostro
Minimum PIO transfer cycle time with IORDY flow control 120 nostro
ATA standard version ATA/ATAPI-7 and below
SMART feature set Supported, Disabled
Security Mode feature set Supported, Disabled
Removable Media feature set Not supported
Power Management feature set Supported
PACKET Command feature set Not supported
Write cache Supported, Enabled
Look-ahead Supported, Enabled
Release interrupt Not supported
SERVICE interrupt Not supported
DEVICE RESET command Not supported
Host Protected Area feature set Supported
WRITE BUFFER command Supported
READ BUFFER command Supported
NOP command Not supported
DOWNLOAD MICROCODE command Supported
READ DMA QUEUED and WRITE DMA QUEUED commands Not supported
CFA feature set Not supported
Advanced Power Management feature set Not supported
Removable Media Status feature set Not supported
Power-Up In Standby feature set Not supported
SET MAX security extension Supported, Disabled
Automatic Acoustic Management feature set Not supported
48-bit Address feature set Supported
Device Configuration Overlay feature set Supported
FLUSH CACHE command Supported
FLUSH CACHE EXT command Supported
SMART error logging Supported
SMART self-test Supported
Media serial number field words Not supported
Media Card Pass Through Command feature set Not supported
Streaming feature set Not supported
General Purpose Logging feature set Supported
WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands Not supported
WRITE DMA QUEUED FUA EXT command Not supported
World wide name Not supported
URG bit for READ STREAM DMA and READ STREAM PIO commands Not supported
URG bit for WRITE STREAM DMA and WRITE STREAM PIO commands Not supported
Time-limited Read/write feature set Not supported
Read Continuoud and Write Continuous in the Time-limited Read/write feature set Not supported
Ultra DMA mode selected Mode 2
Ultra DMA mode supported Mode 5 and below
The time required for the SECURITY ERASE UNIT command to complete Value not specified
Time required for Enhanced security erase unit completion Value not specified
Master Password Revision Code Not supported
Device vendor’s recommended acoustic management level 0
The current automatic acoustic management level 208
Removable Media Status Notification feature set Not supported
Enhanced security erase unit feature Not supported
The security count is expired and SECURITY UNLOCK and SECURITY ERASE UNIT are command aborted until a power-on reset or hardware reset.
CFA Power Mode Mode 1
Maximum average RMS current 32 Milliamperes
Start/Stop Count (Power on count) 110 times
Reallocated Sectors Count 0 sectors
Power-On Hours 517 minuties (hours)
Device Power Cycle Count 111 times
Temperature 27 °C
Current Pending Sector Count (Unstable sectors) 0 sectors
Uncorrectable Sector Count 0 sectors
UltraDMA CRC Error Count (total) 0 errors
Write Error Rate (Multi Zone Error Rate) 0
LupinIII